Hi
everyone, I’ve had a few requests to show how I make some of the silver charms
that I hang on my mixed-media pages and mini books. I showed these on previous
videos and so I just thought I'd share some of the more basic techniques here
and some of the materials that you will need for those.
So
most of my silver charm bracelets start with one
of these, which is a head pin and it's like an ordinary pin and you've got the
pin head there which stops your beads falling off, but obviously it hasn't got
the sharp end like a real pin would and I tend to use the longer ones, which
are 50 millimetre or two inches long and just because it's less fiddly. You can
buy an inch long and various sizes and but I find them quite fiddly to work
with any smaller, so the two inch ones or the 50 millimetre is what I would
normally use and they come in a range of colours.
So
you've got your gold and silver, antique gold, bronze and there's a black one
as well that I’ve seen, and so it depends what type of project that you're
working on, as to what you'd need and the one I'm going to show you how to make
is this one here. The head pin runs through the centre, you can't really see
the tip of it there because I’ve got an extra bead at the bottom, and then you
attach your beads and obviously whatever type of fastening or clasp at the top.
So to make this particular one then, I start with a spacer bead, which these
are three millimetre spacer beads and again you can buy these in the various
colours to match your findings and the reason you might need those and firstly,
obviously as the name suggests, they create a bit of space between your main
beads. If you are using expensive beads, then obviously you'd want to space
those apart a little bit, but if you're using a large bead like this, you often
find the holes are too big to stay on with the tip of your head pin. So you'd
use a spacer bead at the bottom, just to make sure that's secure.
So
I'm going to thread my first and spacer bead onto the head pin and then I'm going
to thread my main bead, which is a lamp work bead, this is 20 millimetre lamp
work bead, and then I'm going to add another one of the round spacer beads. The
same as the one at the bottom. The next type of bead I used on here, these are
also spacer beads, but these are a different type, these are daisy spacer beads
and these particular ones I think are three mil or four mil. So quite small
beads, I'm going to take one of those and this basically is to frame, the next
coloured bead, which you can see that the pink coloured bead there and this one
is the natural gemstone beads.
You
can see those two well and it's rhodolite and it goes particularly well with
the heart-shaped bead that shows. So I'm going to thread the rhodolite bead
onto there and then another, have the daisy spacer beads, and then to finish
I'm going to use another one of the silver spacer beads. So you can use
whatever type of beads that you have, I tend to use a lot of the gemstone,
natural gemstone beads, but they can be quite expensive and I also use a lot of
the Swarovski crystals, which again can be expensive and so if you're just
practicing, you might want to start with maybe acrylic or glass beads which
tend to be cheaper.
The
next thing you need, you do need some quality jewellery
pliers for this. These are round nose pliers because the ends of them
are rounded and that's what you need to form a loop at the top, before you add
any attachments. The other type you can get are called flat nose pliers, which
obviously are, flat inside but these ones you just grasp with the tip of your
plier, and then you literally take your finger and Bend your head pin around
there and then remove your pliers and you will need some wire cutters. Mine
came in a set, you can buy these a reasonable price in a set, you've got
everything you need and then what you need to do is just nip the wire and so
you've got enough wire to form a loop and join it together. So I'm just going
to nip that there and then you take your round nose pliers again, this is going
to be a little bit tricky, I'm trying to do it in film but you need to take
your round nose pliers, right at the very ends, trying to focus the camera. I
don't think it's going to focus too well so close up, but you nip them right
near the end and you need to just twist them so that that loop will join
together.
I'm
just trying to do this quickly and then you need just to make sure that that
loop is closed and it's going to hold those beads in place and then you can
manipulate it if you're not quite happy, it's not straight and you can
obviously manipulate a little bit, but just make sure that it has actually
closed up at the top and sometimes I do take my flat nose pliers at this point
as well, and just flatten it a little bit and close the loop a bit more at the
bottom.
It
is probably the trickiest part, but with a little bit of practice it's you can
do it relatively quickly. The next thing we want to take our jump rings, these
are open jump rings which means when you twist them they're going to open. This
one has just been partially opened, what's important when you're using the jump
rings you don't pull them apart that way, you actually twist them and towards
you to open them. Okay so they look like that when they're open and then you
can hook onto here, obviously it needs to go on the loop on your charm and then
if you've got any clasps or fastenings that you need to go on. For mine I tend
to use 12 mil lobster clasps and but obviously it could be jewellery finding or
anything like that and to make earrings and or whatever it is that you’re
doing, and once you've got it on your jump ring, then you use your jump ring to
attach where you've just formed that hook with your head pin and then you would
twist it closed again. Just twist it until it shuts and then you have your
finished charm.
Okay
probably take a bit more time on yours, the other type you can use, you can use
these, all the findings called eye pins. These have a loop in them already and
I use these if I want to make something that looks a bit longer and dangly, and
these have got jump rings in between. So I'd start off again exactly the same
way. I'd start with and one of the eye pins, got one out and probably start
with taking these beads. So you start with your beads and then you might want
to add possibly a spacer bead in between, and this time instead of adding lots
more beads, you might as I say, might add your spacer bead, but not much more.
You'd form your loop straight away, you would cut that off, okay and then
before you close your and loop, you'd want to attach a jump ring onto there or
you can add your jump ring afterwards. Perhaps it might be easier if you
beginning to close your loop and then add your jump ring, so I’ll show you how
to do that and just close your loop as you did before. Then you need your jump
ring, which you need to twist as we said before, twist to open, put it onto the
loop and then you would take your head pin and also attach that, then close
your loop.
So
you're starting to get that more jingly effect, then you would take your next
bead and you do exactly the same thing, it make your loop okay, cuts it and
close it and then you'd carry on with the next one. So you'd put another jump
ring onto there, another eye pin onto there and carry on until you've got as
many charms on there as you actually want and it would look very long. One
look, something like that with the same finishing technique at the top, so I
hope that's been useful for somebody. I do hope it's focused enough because
it's quite detailed and please leave a comment if you want any more information
on supplies or techniques or anything. Ok thank you for watching bye.
No comments:
Post a Comment